The maximum supply voltage supported by this board is 46V To ensure safely operating condition you can measure the motor current absorption of each motor; this allow to avoid stall conditions. To avoid dangerous overheating condition you can use the integrated I2C digital temperature sensor mounted close to the L chip. To optimize the response to RC commands you also have the calibration function on the receiver signals. For the I2C communication, there are two different slave addresses selectable through a jumper, and in this way it is possible to use two Easy Motor Controllers on the same serial line, and then control them by using a single external controller. On this shield the selection of the power source for motor outputs is accomplished by a jumper. The logic of the Dual DC Motor Shield is powered directly from the Arduino board, whereas motor outputs can be powered both from Arduino Vin pin or from external power source, even if it is strongly encouraged to use external power supply. Maggiori informazioni Read more.

Uploader: Vikazahn
Date Added: 27 September 2006
File Size: 63.66 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 19000
Price: Free* [*Free Regsitration Required]

This shield is based on the L, a high voltage, high current dual full-bridge driver. The logic of the Dual DC Motor Shield is powered directly from the Arduino board, whereas motor outputs can be powered both from Arduino Vin pin or from external power source, even if it is strongly encouraged to use external power supply.

For the I2C communication, there are two different slave addresses selectable through a jumper, and in this way it is possible to use two Easy Motor Controllers on the same serial line, and then control them by using a single external controller. Moving the jumper from one side to the other the power source can be changed.

Microbot | Active Robots

Cookies help us deliver our services. To prevent board damages, all driver lines are diode protected from back EMF.

Last Drivers  DRIVER FOR GA-H81M-S2PV

To ensure safely operating condition you can measure the motor current absorption of each motor; this allow to avoid stall conditions. To optimize the response to RC commands you also have the calibration function on the receiver signals.

Add to project More from Microbot. Do you need a written offer before ordering? We will send you a mail when the product becomes available again Error during request registration Not available.

Dual DC Motor Shield

In fact when the L chip works at high current values it may become very hot and this heat can flow through all the shield. This board also provides direction LED indicators for both channels and this is very usefull during setup stage to verify the firmware behaviour; the led indicators work also without appling a real motor to the output.

The Easy Motor Controller provides two separate power supplies, one for motot motor and the other one for the logic part; the latter can be pulled out through a jumper directly from that of the motor or alternatively from the BEC circuit of the RC receiver.

Cookies help us deliver our services. Maggiori informazioni Read more. We will send you a mail when the product becomes available again Error during request registration Not available. The Dual Jotor Motor Shield is a shield that has been projected to enable an Arduino board to drive two brushed DC motors or one 4-wire two-phase stepper motor, controlling the speed and direction of each one independently.

Microbot Easy Motor Controller Microbot. It is a high voltage, high current dual fullbridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays,solenoids, DC and stepping motors.

The maximum supply voltage supported by this board is 46V. The maximum supply voltage micrpbot by this board is 30V.

Last Drivers  HP PAVILION DV5 1070EE DRIVER DOWNLOAD

The Easy Motor Controller allows to control the speed and the direction of rotation of a DC motor through three different possible inputs: The maximum supply voltage supported by microbpt board is 46V To mootor safely operating condition you can measure the motor current absorption of each motor; this allow to avoid stall conditions.

It is based on the famous integrated circuit L, producted by STMicroelectronics; the L is an integrated monolithic circuit in a PowerSO20 package.

Make Dumb Devices Smart

To enable or disable each channel independently of the input signals there are provided two enable inputs E1, E2 positioned on the front of the board; motor moor regulation is obtained applying to these pins a PWM signal with a 20KHz max.

On this shield it has been included an integrated I2C digital temperature sensor to monitor the shield temperature in order to prevent overtemperature threat.

Microbot Easy Motor Controller. By using our services, you agree to our use of cookies. All kicrobot after this time will be shipped again from It has direction leds for help testing operations. The minimum supply voltage allowed is 7V, so you can use also two-cell LiPo batteries 7. On this shield the selection of the power source for motor outputs is accomplished by a jumper.

Microbot Easy Motor Controller

We would like to ask you to consider this in your order planning! Maggiori informazioni Read more. To avoid dangerous overheating condition you can use the integrated I2C digital temperature sensor mounted close to the L chip.